Multi-Band Operation
Spread-spectrum frequency Hopping
Link Budget
One-way latency
Refresh, 16 ch
WHERE UbiC2™ FITS
Resilient control at low size, weight, power, and cost
Interference resilience
Architecture
Multi-band range
Size / power / cost
Low-cost open links
Weak
Fixed-band radio
One band
Fragile
High-end radios
Strong
Wideband OFDM radio
Limited per variant
Large, power, hungry, costly
Strong — cross-band FHSS
Software-defined SS-FH
~2 GHz (660–2700 MHz)
Cost-effective; small, light, low-power
NDAA-compliant
WHY UbiC2™
The resilience lives in the waveform, not in heavy hardware — so UbiC2 is compact, low-power, and built from NDAA-compliant components.
Cross-band frequency hopping spreads transmissions over many pre-set channels across ~2 GHz, and spread-spectrum processing gain pulls the signal out of noise — so the link stays stable as long as some channels are clear, even in congested or noisy RF.
Native CRSF over the standard interface — mounts in a JR-bay controller and pairs with ArduPilot, PX4, or Betaflight. Upgrade the RF link with a module swap, not a redesign.
143 dB link budget and −115 dBm sensitivity reach long range at just 28 dBm (630 mW) — light and power-efficient.
Band and channel selection are software settings, configured before each deployment. Coverage to 2.7 GHz arrives in Q4 2026 — one module covers the full range, with no hardware change.
ADOPT WITHOUT REDESIGN
Your existing flight controller
CRSF/UART
S.Port
telemetry
Transmitter Module
Reciver Module
CRSF/UART
S.Port
telemetry
Your existing flight controller ArduPilot PX4 Betaflight
Built for demanding real-world environments
Reliable command and telemetry at long range when infrastructure is down and spectrum is crowded
Stable control for bridge, power-line, and pipeline surveys in RF-noisy, hard-to-reach sites
A dependable control link for … visual-line-of-sight flights ov… and industrial areas.
The paragraph is covered by the Figma toolbar in this screenshot.
Secure, resilient control for search- rescue and emergency operations.
Waveform
PlatinumWave™ SS-FH
Refresh rate
16 ch @ 125 Hz
Link budget
143 dB
Rx sensitivity
-115 dBm
Interface
CRSF/UART · S.Port · USB-C
Frequency range
660 – 2700 MHz
One-way latency
< 15 ms
Transmit power
up to 28dBm
Operating temp
-30 to +70 °C
Dimension
55.6 × 39.2 × 9.4 mm
Weight
10.5 g
Dimension
41.1 × 37.2 × 6.5 mm
Weight
8.5 g
PlatinumWave™ SS-FH · Software-Defined Radio · NDAA-Compliant
Why just 28 dBm reaches beyond 30 km (low band)
Range is set by the link budget — the signal margin between transmitter and receiver — and UbiC2 wins that budget in the waveform, not with brute-force power. Its PlatinumWave™ SS-FH waveform adds roughly 17 dB of link budget versus a conventional wideband radio at the same C2 data rate: about 12 dB from spread-spectrum processing gain (de-spreading recovers the signal from below the noise floor) plus about 4 dB from operating in a narrow C2 channel with a lower noise floor.
That is what delivers a 143 dB link budget and −115 dBm sensitivity — and why UbiC2 reaches beyond 30 km in the low band on just 28 dBm (630 mW), where a wideband radio would need tens of watts. Longer range, lighter hardware, lower power.
